Showing results: 541 - 555 of 657 items found.
-
Keysight Technologies
Keysight's PNA-X is more than just a vector network analyzer. It is the world’s most integrated and flexible microwave test engine for measuring amplifiers, mixers, frequency converters, and other active devices. The hardware includes two internal signal sources, a signal combiner, S-parameter and noise receivers, pulse modulators and generators, and a flexible set of switches and RF access points. These hardware features provide a powerful core for a broad range of linear and nonlinear measurements, all with a single set of connections to your device under test.
-
Praxsym
Low Noise Pre-Amplifier and companion external low noise amplifier (LNA) are used to amplify low level microwave signals. The Pre-Amplifier contains an AC/DC power supply, internal low noise amplifier, and a bias tee to source a DC bias voltage on the RF input connector.To overcome cable loss between the test antenna and the Pre-Amplifier assembly, a remote low noise amplifier (LNA) is mounted directly onto the 10 GHz antenna. A bias tee inside the Pre-Amplifier chassis powers the remote LNA through the coax cable interconnecting the pre-amplifier and the 10 GHz test antenna.
-
44500 -
M. C. Miller Company
Rugged, lightweight case - safe to use on wet ground• Weatherproof, even with lid removed - IP67 rating for dust and water intrusion• Convenient case lid removal for ease of movement, with test leads attached, to new measurement locations• Resistance measurement range from 0.01Ω to 1.1MΩ • Resistance measurements are unaffected by any stray interference signals that may be present in the earth during readings, due to the use of narrow band-pass filters centered at 97Hz (the unit’s operating frequency)• Runs on a set of C-cell alkaline batteries...no need to periodically recharge the unit or to plug it into a power source
-
Furaxa, Inc.
These devices provide two synchronized DDS-based RF channels on a single PCI card. With fine frequency, amplitude and phase control the Synth1000 products enable a number of advanced applications at a fraction of the cost of conventional equipment. In addition to two analog outputs the Synth1000, up to 4 separate profiles may be dynamically selected using externally supplied TTL signals for low-latency triggered operation such as PSK, FSK, and triggered sweep operation. Software support for Windows 8, 7, Vista, Windows XP and Linux is included. LabVIEW Labview source code available. For detailed specifications, please refer to the Synth1000 Manual.
-
Thorlabs, Inc.
Thorlabs' Fused Polarization Maintaining (PM) Wavelength Division Multiplexers (WDMs) combine two wavelengths of light in PM fiber while maintaining the polarization of the incident light. These WDMs are reversible; they can also be used to split two discrete wavelengths entering the common port into two separate output ports. They are not designed to split the output from a broadband source. PM WDMs are often used for pump / signal applications that incorporate erbium-doped or ytterbium-doped fiber amplifiers. They can be readily customized for a wide variety of applications, enabling rapid design cycles and new project builds. For custom requests, please contact Tech Support.
-
PLC-1 × 口口口 -
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai Planar Optical Waveguide Optical Splitter (PLC Splitter) is an integration waveguide optical power distribution device that based on quartz substrate, featured with small size, wide working wavelength range, high reliability and excellent uniformity of optical split, etc. It is especially suitable for connecting local unit with terminal unit in passive optical network (EPON, BPON, GPON, etc.) to achieve optical signal splitting. The main design divide optical signal in optical communication system into multi-way output. The component that we manufactured is with high stability to light source and temperature. And diversified packages can meet customers’ different requirements in application. According to the various requirements, our PLC splitter is with various types: bare fiber type, miniature type, fan-out type, module type, tray type, plug-in type , Blade package type, rack-mounted type, etc.
-
PLC-2 × 口口口 -
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai Planar optical waveguide optical splitter (PLC Splitter) is an integration waveguide optical power distribution device that based on quartz substrate, featured with small size, wide working wavelength range, high reliability and excellent uniformity of optical split, etc. It is especially suitable for connecting local unit with terminal unit in passive optical network (EPON, BPON, GPON, etc.) to achieve optical signal splitting. The main design divide optical signal in optical communication system into multi-way output. The component that we manufactured is with high stability to light source and temperature. And diversified packages can meet customers’ different requirements in application. According to the various requirements, our PLC splitter is with various types: bare fiber type,miniature type, fan-out type,module type, tray type, plug-in type , Blade package type, rack-mounted type, etc.
-
785659-01 -
NI
The TriaxM-TriaxM Triaxial Cable connects your system to PXI Source Measure Units and other devices that have a triaxial connector. It uses guarding to remove the effects of leakage current and parasitic capacitance when … measuring very low current signals. The cable offers 300 V DC maximum voltage, 3 A maximum continuous current, 10 A maximum pulsed current, and different lengths.
-
785659-03 -
NI
The TriaxM-TriaxM Triaxial Cable connects your system to PXI Source Measure Units and other devices that have a triaxial connector. It uses guarding to remove the effects of leakage current and parasitic capacitance when … measuring very low current signals. The cable offers 300 V DC maximum voltage, 3 A maximum continuous current, 10 A maximum pulsed current, and different lengths.
-
Model 2205 -
TREK, INC.
The Trek Model 2205 is a member of Trek’s 2200-series of high-voltage 40 W amplifiers that offesr high performance at an attractive price. It incorporates DC stability, wide bandwidth, well regulated and controlled AC output signals, full four-quadrant class AB all-solid-state output stages, DC offset adjustment with front panel metering, and autorecovery shutdown to protect the output from being overpowered. The instrument also stage sinks or sources current into reactive or resistive loads throughout the output voltage range which makes it ideal to achieve the accurate output response and high slew rates demanded by reactive loads.
-
SYNTH300 SERIES -
Ultraview Corporation
These devices provide two synchronized DDS-based RF channels on a single PCI card. With fine frequency and phase control, triggered operation, and the ability to accept an external clock, the Synth300 products enable a number of advanced applications at a fraction of the cost of conventional equipment. In addition to two analog outputs, the product can be ordered with one (or two) LVDS outputs for programmable digital clock applications, and can be configured for control by externally supplied TTL signals for low-latency triggered operation such as PSK, FSK, and triggered sweep operation.Software support for Windows Vista, Windows XP,Linux and Labview source code availableFor detailed specifications, please refer to the Synth300_Manual
-
DD-1+ -
D'Amore Engineering llc
The purpose of this tool is to enable the installer to set the gain of an audio amplifier to match the source unit's output level, accurately and quickly. It can also be useful for detecting distortion in the audio signal caused by poorly designed or malfunctioning audio equipment. Sets audio system gain overlap, continuously variable from 0.0dB - 15.0dB in 0.1dB steps Checks gain overlap of an audio system without making any adjustments to the existing settings Verifies that the gain overlap of an install hasn't been tampered with after install Features our Patent Pending Distortion Detection system plus digital microcontroller and our proprietary firmware
-
Pickering Interfaces Ltd.
Linear variable differential transformers (LVDT) are electrical transformer sensors to measure linear displacement. Driven by an AC excitation source, the LVDT generates a pair of AC output signals modulated according to the core's mechanical position (displacement). LVDTs have been widely used in applications such as power turbines, hydraulics, automation, aircraft, satellites, nuclear reactors, and many others. These transducers have low hysteresis and excellent repeatability.
-
B-1020 -
ROSS ENGINEERING CORPORATION
*Wideband: DC to over 30MHz*Maximum Output: to 10V PK, 20V PK-PK*Maximum Input: ±5V to ±200V PK-PK as required. Also to 900kV PK with Ross Voltage Divider*Signal Isolation: 500,000 Ohm 450V PK*Input Impedance: Up to 2 Megohms*Load Impedance: 50 Ohm or greater*Power Source: AC or Optional Battery*Will drive over 500 Feet of Coaxial Cable
-
Acces I/O Products, Inc.
Sometimes your sensors or the piece of equipment you are trying to control is not in a convenient place to have a PC close by. The sensors may be widely distributed through out your plant and it just wouldn’t be cost effective to run all your wiring to where the PC is. In addition, low level signals are more accurately acquired when digitized close to the signal source. In all these cases our REMOTE ACCES line of products will help. The REMOTE ACCES pods are intelligent, sensor to computer interfaces. Each pod can be used as an autonomous data logger to acquire data for later download. Or as many as 31 pods may be connected on a single two wire multidrop RS-485 network allowing a cable distance of up to 4000 ft. You can also go wireless and extend your range by adding RS-485 wireless transceivers to your serial port. Each unit comes in a rugged NEMA 4 enclosure and can withstand harsh industrial and marine environments.
